Install Active Directory Domain Services in pictures, Install Active Directory Domain Services ,Windows Server 2008

28 October 2017

Install Active Directory Domain Services in pictures, Install Active Directory Domain Services ,Windows Server 2008

Since Windows 2000, Active Directory has been the driving force behind Microsoft Server Networking Services.
Active Directory provides the structure to centralize the network and store information about network resources across the entire domain. Active Directory uses Domain Controllers to keep this centralized storage available to network users.
In this scenario we are going to install Active Directory fresh with a brand new Domain Controller after a fresh install of Windows Server 2008.

Requirements for Active Directory Domain Services

Let’s go through some of the requirements for a fresh install of Active Directory Domain Services. Some of these will be required to be done before hand; others as noted can be done during the install:

Install Windows Server 2008
Configure TCP/IP and DNS networking configurations
The disk drives that store SYSVOL must be on a local drive configured NTFS
Active Directory requires DNS to be installed in the network. If it is not already installed you can specify DNS server to be installed during the Active Directory Domain Services installation.

Once you verify that these requirements have been met we can get started.

How to Install Active Directory Domain Services via Server Manager

For the first example let’s start by installing Active Directory through Server Manager. This is the most straight forward way, as a wizard will guide you through the steps necessary.
1. Start Server Manager.
2. Select Roles in the left pane, then click on Add Roles in the center console.

3. Depending on whether you checked off to skip the Before You Begin page while installing another service, you will now see warning pages telling you to make sure you have strong security, static IP, and latest patches before adding roles to your server.
If you get this page, then just click Next.

4. In the Select Server Roles window we are going to place a check next to Active Directory Domain Services and click Next.

5. The information page on Active Directory Domain Services will give the following warnings, which after reading, you should click Next:

Install a minimum of two Domain Controllers to provide redundancy against server outage (which would prevent users from logging in with only one)
AD DS requires DNS which if not installed you will be prompted for
After installing AD DS you must run dcpromo.exe to upgrade to a fully functional domain controller
Installing AD DS will also install DFS Namespaces, DFS Replication, and Filer Replication services which are required by Directory Service

6. The Confirm Installation Selections screen will show you some information messages and warn that the server may need to be restarted after installation. Review the information and then click Next.

7. The Installation Results screen will hopefully show Installation Succeeded, and an additional warning about running dcpromo.exe (I think they really want us to run dcpromo).
After you review the, click Close.

8. After the Installation Wizard closes you will see that server manager is showing that Active Directory Domain Services is still not running. This is because we have not run dcpromo yet.

9. Click on the Start button, type dcpromo.exe in the search box and either hit Enter or click on the search result.

10. The Active Directory Domain Services Installation Wizard will now start. There are links to more information if you want to learn a bit more you can follow them or you can go ahead and click Use advanced mode installation and then click Next.

11. The next screen warns about some operating system compatibility with some older clients.
For more information you can view the support documentation from Microsoft and after you have read through it go ahead and click Next.

12. Next is the Choose Deployment Configuration screen and you can choose to add a domain to an existing forest or create a forest from scratch. Choose Create a new domain in a new forest and click Next.

13. The Name the Forest Root Domain wants you to name the root domain of the forest you are creating.
For the purposes of this test we will create ADExample.com. After typing that go ahead and click Next.

14. The wizard will test to see if that name has been used, after a few seconds you will then be asked for the NetBios name for the domain. In this case I will leave the default in place of ADEXAMPLE, and then click Next.

15. The next screen is the Set Forest Functional Level that allows you to choose the function level of the forest.
Since this is a fresh install and a new forest with no additional prior version domains to worry about I am going to select Windows Server 2008. If you did have other domain controllers at earlier versions or had a need to have Windows 2000 or 2003 domain controllers (because of Exchange for example), then you should select the appropriate function level.
Select Windows Server 2008 and then click Next.

16. Now we come to the Additional Domain Controller Options where you can select to install a DNS server, which is recommended on the first domain controller.
If this was not the first domain controller you would have the options of installing Global Catalog and/or setting this as a Read-only Domain Controller. Since it is the first domain controller, Global Catalog is mandatory, and a RDOC controller is not an available option.
Let’s install the DNS Server by placing a check next to it and clicking Next.

17. You will get a warning window about delegation for this DNS server cannot be created, but since this is the first DNS server you can just click Yes and ignore this warning.

18. Next you can choose to place the files that are necessary for Active Directory, including the Database, Log Files, and SYSVOL.
It is recommended to place the log files and database on a separate volume for performance and recoverability. You can just leave the defaults though and click Next.

19. Now choose a password for Directory Services Restore Mode that is different than the domain password. Type your password and confirm it before hitting Next.
Note: You should use a STRONG password for this and will be warned if it doesn’t meet criteria.

20. Next you will see a summary of all the options you have went through in the wizard.
If you plan on creating more domain controllers with the same settings hit the Export settings … button to save off a txt copy of the settings to use in an answer file for a scripted install. After exporting and reviewing settings click on Next.

21. Now the installation will start including the DNS server option if selected. You will notice a box to Reboot on completion that you can check to reboot soon as everything is installed (A reboot is required you can do it manually or use this function to do it automatically).
NOTE: This can be from a few minutes to several hours depending on different factors.

Confirming Active Directory Domain Services Install

When you reboot you will be asked to login to the domain, and be able to open Active Directory Users and Computers from the Administrative menu. When you do you will see the domain ADExample.com and be able to manage the domain.

You have now successfully installed Active Directory Domain Services and the first Domain Controller.